CustomGimbals
rue Raoul Briquet
62217 Achicourt
France
We ship worldwide

AlexMos 32 bits Brushless Camera Stabilizer Strong Motor Encoder Kit

Build Your Own Strong Camera Stabilizer Kit!

SKU: 2SGRNL1827
Delivery date: Manufactured Per Order Request, Dispatched in 2 weeks
*
*
*
*
*
*
81.18 €
excluding shipping

AlexMos 32 bits
Strong Motor Integration Camera Stabilizer Kit

Product Description:

This AlexMos kit is an authorized licencing BASECAM electronics product.

Alexmos 32 bits
Stator diameter 43mm

Using encoders with SimpleBGC controllers gives the following advantages:

  1. Prevents motors from losing synchronization and skipping steps.
  2. Provides the information about frame angle and angle of the camera relative to frame, that can be important for some kind of applications.
  3. For many cases it can significantly decrease power consumption by using field-oriented control strategy to drive motors.
  4. Increases instant torque in the same way.
  5. Allows the controller to get information about the camera balance for automatic balancing (with help of extra DC servo motors and moving counterweights).
  6. The firmware also retains an option to adjust camera position by hands.
  7. Increases the precision of stabilization by applying FOC-specific compensations.

Package included:

– 1 x 32Bit main board
– 1 x Motor with encoder
– 1 x IMU
– 1 x Slipring
– External output cables
– Can operate as single tilt axis, pan / tilt axis or yaw pan tilt axis depending how many motors you ordering.

Input power: 3S Li (11V) or up to 6S with external voltage regulator
Operating Current: [email protected]
Attitude control accuracy: ± 0.02 degrees
Controllable rotation range
Rotation direction (PAN): ± 360 ° unlimited turns
Tilt direction (TILT): ± 360 ° unlimited turns
Rolling direction (ROLL): ± 360 ° unlimited turns
SBUS / PPM / SPI receiver support
Alexmos 32 bits licensed version
Ubec +5v 1A max

 

Model

4310

4315

6010

Weight (g) W/O encoder housing

112

158

235

Stator dimension (mm)

43x10

43x15

60x10

Configuration

24N28P

24N28P

245N28P

Turns

60

60

90

Voltage (V)

12-24

12-24

12-24

Torque

[email protected]

[email protected]

[email protected]

Resistance (Ohm)

11.0

15.2

10.3

Weight of Camera Stabilizer with camera (g)

1000-2000g

1500-3000g

2500-4000g

Encoder

AS5048A

AS5048A

AS5048A

Encoder connector

Standard PWM, SBUS (optional: SPI)

Standard PWM, SBUS (optional: SPI)

Standard PWM, SBUS (optional: SPI)

Slip ring

12.5mm

12.5mm

12.5mm or 22mm

 

Documentation link
Basecam Official Documentation

Tuning Guide:

- We recommend to NOT UPGRADE THE ALEXMOS KIT TO THE LATEST VERSION OR YOU WILL BRICK IT

- THIS IS NOT A PLUG AND PLAY DEVICE! Brushless Camera Stabilizers and controllers are very new to the market and is an emerging technology. You will need some patience and effort to get it to work as seen in many youtube videos. We can assist you while setting up the devise.

- This product has no protection circuit, it will be damaged due to power supply polarity reversed; wrong motor will burn down driver IC; Also, incorrect connection of attitude sensor will burn down the voltage regulation unit. The cases above are not covered under the warranty.

NOTE:

We carry this product is for customer’s convenience to purchase. We will always assume you are capable of handling this kind of open source project by yourself as we can’t provide comprehensive technical support as you may expect. And we don’t recommend this product if you don’t have confidence to use it. Please refer to the official website and related forums for the open source project if you have any questions.

PLEASE NOTE sliprings cables does not have any pins management
You will need to wire them directly to the encoder by soldering them to the board

 

You Didn't Find Your Gimbal?

That means we didn't work enough. Start a conversation with our technicians by chat or by contact page, they will be happy to answer you asap with the most suitable solution for your needs.


Why ordering gimbals here?

Here you won't find some chinese rebranded gimbals.

We manufacture the whole gimbal parts that means

- Motors

- Gimbal controller

- Camera mount

- Frame mount

 

What if i crash my Copterlab gimbal?

 

Each part can be replaced easily by cheap offer as we manufacture each part of the gimbals we sell

 

What if i'm running under issue with my Copterlab gimbal?

 

Our support will reply you quickly by email or live chat support. After purchasing, you stay our priority.

 
 

What if i can't find model i'm searching for?

 

Just contact us and we will design custom parts for free!)

 

I just want to get the electronic and motors gimbal parts

Just click here

 
Designed in NevadaMade in France
We stand for USA